22#ifndef _SERIAL_WOMBAT_ERROR_
23#define _SERIAL_WOMBAT_ERROR_
@ SW_ERROR_UNKNOWN_INPUT_PROCESS_COMMAND
(#45) The command index for an inputProcess command is not supported on this firmware
@ SW_ERROR_2ND_INF_WRONG_UNLOCK
(#25) The unlock value provided to enable the 2nd interface was incorrect.
@ SW_ERROR_INVALID_PARAMETER_6
(#20) The pin configuration parameter in Byte 6 was invalid
@ SW_ERROR_WS2812_INDEX_GT_LEDS
(#14) The command references an index that is greater or equal to the number of leds
@ SW_ERROR_CMD_BYTE_3
(#30) Byte 3 of the command was invalid
@ SW_ERROR_INVALID_PARAMETER_7
(#21) The pin configuration parameter in Byte 7 was invalid
@ SW_ERROR_CMD_BYTE_4
(#31) Byte 4 of the command was invalid
@ SW_ERROR_LESS_THAN_8_BYTES_RETURNED
(#48) The Serial Wombat Chip returned less than 8 bytes (Used at host level, not firmware)
@ SW_ERROR_PIN_NUMBER_TOO_HIGH
(#22) The pin number indicated was greater than the greatest avaialable pin
@ SW_ERROR_WUB_INVALID_ADDRESS
(#8) An attempt to write to a user buffer address outside the user buffer was attempted.
@ SW_ERROR_RUB_INVALID_ADDRESS
(#43) An attempt to read user buffer address outside the user buffer was attempted.
@ SW_ERROR_CMD_BYTE_1
(#28) Byte 1 of the command was invalid
@ SW_ERROR_HW_RESOURCE_IN_USE
(#16) The requested hardware or software resource in use has already been exclusively claimed by anot...
@ SW_ERROR_WUB_COUNT_GT_4
(#7) A count greater than 4 was provided as a number of bytes to write to count user buffer
@ SW_ERROR_PULSE_ON_CHANGE_ENTRY_OUT_OF_RANGE
(#46) The pulse on change entry number exceeded the number of entries
@ SW_ERROR_QUEUE_RESULT_INSUFFICIENT_USER_SPACE
(#36)
@ SW_ERROR_UNKNOWN_PIN_MODE
(#3) A Pin mode was indicated that is not avaialble on this model or version of Serial Wombat chip
@ SW_ERROR_INSUFFICIENT_SPACE
(#6) There was not sufficient space in the queue or user area to complete the command.
@ SW_ERROR_INVALID_PARAMETER_3
(#17) The pin configuration parameter in Byte 3 was invalid
@ SW_ERROR_CMD_BYTE_5
(#32) Byte 5 of the command was invalid
@ SW_ERROR_PIN_NOT_CAPABLE
(#15) The commanded pin does not have the hardware support to perform the commanded pin mode
@ SW_ERROR_ASCII_NUMBER_TOO_BIG_16
(#2) A number bigger than 65535 was provided to convert to a 16 bit value
@ SW_ERROR_QUEUE_RESULT_UNALIGNED_ADDRESS
(#37)
@ SW_ERROR_RF_ODD_ADDRESS
(#10) Addresses Read From Flash must be even.
@ SW_ERROR_FLASH_WRITE_INVALID_ADDRESS
(#11) An attempt to write or erase flash was made to a protected or non-existant area
@ SW_ERROR_UNKNOWN_OUTPUTSCALE_COMMAND
(#44) The command index for an output scaling command is not supported on this firmware
@ SW_ERROR_CMD_UNSUPPORTED_BAUD_RATE
(#35) invalid baud rate enumeration
@ SW_ERROR_QUEUE_RESULT_INVALID_QUEUE
(#38)
@ SW_ERROR_UART_NOT_INITIALIZED
(#27) A UART operation was requested but the UART was not intialized
@ SW_ERROR_CMD_BYTE_7
(#34) Byte 7 of the command was invalid
@ SW_ERROR_QUEUE_RESULT_EMPTY
(#40)
@ SW_ERROR_PINS_MUST_BE_ON_SAME_PORT
(#1) Pins must be on the same microcontroller part (e.g. PORTA, PORTB, etc.). See datasheet of micro ...
@ SW_ERROR_DATA_NOT_AVAILABLE
(#41)
@ SW_ERROR_INVALID_COMMAND
(#5) The first byte of a received packet does not correspond with a command supported by this model o...
@ SW_ERROR_REENTRANCY_NOT_SUPPORTED
(#49) The library was used in an unsupported manner, such as calling a communication command from an ...
@ SW_ERROR_INVALID_PIN_COMMAND
(#12) The pin command 0xC1, 0xC2, etc is not suported by this pin mode (May vary by model)
@ SW_ERROR_RESET_STRING_INCORRECT
(#4) A Packet starting with 'R' was received but didn't have the correct following bytes to cause a r...
@ SW_ERROR_ANALOG_CAL_WRONG_UNLOCK
(#24) The unlock value provided to write analog calibration was incorrect.
@ SW_ERROR_QUEUE_RESULT_FULL
(#39)
@ SW_ERROR_PIN_IS_COMM_INTERFACE
(#23) The pin number indicated is currently being used for Serial Wombat protocol communicaitons
@ SW_ERROR_CMD_BYTE_6
(#33) Byte 6 of the command was invalid
@ SW_ERROR_WUB_CONTINUE_OUTOFBOUNDS
(#9) A call to Write User Buffer Continue would have written out of bounds.
@ SW_ERROR_INVALID_PARAMETER_4
(#18) The pin configuration parameter in Byte 4 was invalid
@ SW_ERROR_PIN_CONFIG_WRONG_ORDER
(#13) The called pin command 0xC1, 0xC2 was called before other required prior commands (e....
@ SW_ERROR_CMD_BYTE_2
(#29) Byte 2 of the command was invalid
@ SW_ERROR_TM1637_WRONG_MODE
(#42) The TM1637 pin is configured for the wrong TM1637 mode to process the command
@ SW_ERROR_2ND_INF_UNAVAILABLE
(#26) The 2nd interface hardware was not avaialble to claim
@ SW_ERROR_UNNUMBERED_ERROR
(#32767)
@ SW_ERROR_PULSE_ON_CHANGE_UNKNOWN_MODE
(#47) The pulse on change Mode requested is unknown
@ SW_ERROR_INVALID_PARAMETER_5
(#19) The pin configuration parameter in Byte 5 was invalid