| Enumerator |
|---|
| SW_ERROR_UNNUMBERED_ERROR | (#32767)
|
| SW_ERROR_PINS_MUST_BE_ON_SAME_PORT | (#1) Pins must be on the same microcontroller part (e.g. PORTA, PORTB, etc.). See datasheet of micro for port assignments.
|
| SW_ERROR_ASCII_NUMBER_TOO_BIG_16 | (#2) A number bigger than 65535 was provided to convert to a 16 bit value
|
| SW_ERROR_UNKNOWN_PIN_MODE | (#3) A Pin mode was indicated that is not avaialble on this model or version of Serial Wombat chip
|
| SW_ERROR_RESET_STRING_INCORRECT | (#4) A Packet starting with 'R' was received but didn't have the correct following bytes to cause a reset
|
| SW_ERROR_INVALID_COMMAND | (#5) The first byte of a received packet does not correspond with a command supported by this model of Serial Wombat chip
|
| SW_ERROR_INSUFFICIENT_SPACE | (#6) There was not sufficient space in the queue or user area to complete the command.
|
| SW_ERROR_WUB_COUNT_GT_4 | (#7) A count greater than 4 was provided as a number of bytes to write to count user buffer
|
| SW_ERROR_WUB_INVALID_ADDRESS | (#8) An attempt to write to a user buffer address outside the user buffer was attempted.
|
| SW_ERROR_WUB_CONTINUE_OUTOFBOUNDS | (#9) A call to Write User Buffer Continue would have written out of bounds.
|
| SW_ERROR_RF_ODD_ADDRESS | (#10) Addresses Read From Flash must be even.
|
| SW_ERROR_FLASH_WRITE_INVALID_ADDRESS | (#11) An attempt to write or erase flash was made to a protected or non-existant area
|
| SW_ERROR_INVALID_PIN_COMMAND | (#12) The pin command 0xC1, 0xC2, etc is not suported by this pin mode (May vary by model)
|
| SW_ERROR_PIN_CONFIG_WRONG_ORDER | (#13) The called pin command 0xC1, 0xC2 was called before other required prior commands (e.g. 0xC0)
|
| SW_ERROR_WS2812_INDEX_GT_LEDS | (#14) The command references an index that is greater or equal to the number of leds
|
| SW_ERROR_PIN_NOT_CAPABLE | (#15) The commanded pin does not have the hardware support to perform the commanded pin mode
|
| SW_ERROR_HW_RESOURCE_IN_USE | (#16) The requested hardware or software resource in use has already been exclusively claimed by another pin
|
| SW_ERROR_INVALID_PARAMETER_3 | (#17) The pin configuration parameter in Byte 3 was invalid
|
| SW_ERROR_INVALID_PARAMETER_4 | (#18) The pin configuration parameter in Byte 4 was invalid
|
| SW_ERROR_INVALID_PARAMETER_5 | (#19) The pin configuration parameter in Byte 5 was invalid
|
| SW_ERROR_INVALID_PARAMETER_6 | (#20) The pin configuration parameter in Byte 6 was invalid
|
| SW_ERROR_INVALID_PARAMETER_7 | (#21) The pin configuration parameter in Byte 7 was invalid
|
| SW_ERROR_PIN_NUMBER_TOO_HIGH | (#22) The pin number indicated was greater than the greatest avaialable pin
|
| SW_ERROR_PIN_IS_COMM_INTERFACE | (#23) The pin number indicated is currently being used for Serial Wombat protocol communicaitons
|
| SW_ERROR_ANALOG_CAL_WRONG_UNLOCK | (#24) The unlock value provided to write analog calibration was incorrect.
|
| SW_ERROR_2ND_INF_WRONG_UNLOCK | (#25) The unlock value provided to enable the 2nd interface was incorrect.
|
| SW_ERROR_2ND_INF_UNAVAILABLE | (#26) The 2nd interface hardware was not avaialble to claim
|
| SW_ERROR_UART_NOT_INITIALIZED | (#27) A UART operation was requested but the UART was not intialized
|
| SW_ERROR_CMD_BYTE_1 | (#28) Byte 1 of the command was invalid
|
| SW_ERROR_CMD_BYTE_2 | (#29) Byte 2 of the command was invalid
|
| SW_ERROR_CMD_BYTE_3 | (#30) Byte 3 of the command was invalid
|
| SW_ERROR_CMD_BYTE_4 | (#31) Byte 4 of the command was invalid
|
| SW_ERROR_CMD_BYTE_5 | (#32) Byte 5 of the command was invalid
|
| SW_ERROR_CMD_BYTE_6 | (#33) Byte 6 of the command was invalid
|
| SW_ERROR_CMD_BYTE_7 | (#34) Byte 7 of the command was invalid
|
| SW_ERROR_CMD_UNSUPPORTED_BAUD_RATE | (#35) invalid baud rate enumeration
|
| SW_ERROR_QUEUE_RESULT_INSUFFICIENT_USER_SPACE | (#36)
|
| SW_ERROR_QUEUE_RESULT_UNALIGNED_ADDRESS | (#37)
|
| SW_ERROR_QUEUE_RESULT_INVALID_QUEUE | (#38)
|
| SW_ERROR_QUEUE_RESULT_FULL | (#39)
|
| SW_ERROR_QUEUE_RESULT_EMPTY | (#40)
|
| SW_ERROR_DATA_NOT_AVAILABLE | (#41)
|
| SW_ERROR_TM1637_WRONG_MODE | (#42) The TM1637 pin is configured for the wrong TM1637 mode to process the command
|
| SW_ERROR_RUB_INVALID_ADDRESS | (#43) An attempt to read user buffer address outside the user buffer was attempted.
|
| SW_ERROR_UNKNOWN_OUTPUTSCALE_COMMAND | (#44) The command index for an output scaling command is not supported on this firmware
|
| SW_ERROR_UNKNOWN_INPUT_PROCESS_COMMAND | (#45) The command index for an inputProcess command is not supported on this firmware
|
| SW_ERROR_PULSE_ON_CHANGE_ENTRY_OUT_OF_RANGE | (#46) The pulse on change entry number exceeded the number of entries
|
| SW_ERROR_PULSE_ON_CHANGE_UNKNOWN_MODE | (#47) The pulse on change Mode requested is unknown
|
| SW_ERROR_LESS_THAN_8_BYTES_RETURNED | (#48) The Serial Wombat Chip returned less than 8 bytes (Used at host level, not firmware)
|
| SW_ERROR_REENTRANCY_NOT_SUPPORTED | (#49) The library was used in an unsupported manner, such as calling a communication command from an interrupt when communication was in progress
|
1.13.2